<img alt="" src="https://secure.hims1nice.com/150891.png" style="display:none;">

Concrete Casting News from the Hill and Griffith Company

Repairing Bug Holes

Posted by Hill and Griffith Company on Dec 24, 2020 8:00:00 AM

Excerpt from Concrete Construction's August 2012 Q&A Article by Kim Basham

QUESTION: About 2 months ago, we finished placing a concrete foundation for a large commercial building and now the owner is complaining about surface bug holes. The bug holes are fairly small (less than ½ inch wide) but occur fairly frequently in some places. Until the painters started painting the walls, everyone was pleased with our work.

Now, the owner claims the bug holes are unacceptable because they distract from the overall appearance of the painted walls. The owner claims the bug holes are defects and we are responsible for fixing them.

Are bug holes defects? Are we responsible for repairs?

Concrete Bug Hole Repair

 

ANSWER: ACI 347-04, "Guide to Formwork for Concrete," defines bug holes, or surface voids, as small regular or irregular cavities, usually not exceeding about 5/8 inch (or 15 mm) in diameter, resulting from entrapment of air bubbles in the surface of formed concrete during placement and consolidation.

Bug holes commonly occur in vertical cast-in-place concrete such as walls, columns, beams, etc. Both the number and size of bug holes vary and depend on many factors. These include form facing material and condition, release agent type and application thickness, concrete mix characteristics, and placing and consolidation practices.

The permissible number and size of bug holes in a concrete surface is not defined in either ACI 301-05 or ACI 301-10, "Specifications for Structural Concrete." In fact, ACI 301-05 does not limit either the number or size of surface voids in as-cast surface finishes.

ACI 301-05 specifies two as-cast surface finishes: rough-form and smooth-form. While it does list other requirements for rough- and smooth-form finishes, it does not limit the permissible number or size of bug holes.

Rough- and smooth-form finishes have been dropped in the more recent 2010 version of ACI 301. Now, as-cast surface finishes are SF-1.0, SF-2.0, and SF-3.0. Like ACI 301-05, ACI 301-10 does not limit either the number or size of bug holes in as-cast surface finishes.

However, ACI 301-10 does limit the maximum size of surface voids to 1½ inches wide or ½ inch deep for SF-1.0, and 3/4 inch wide or ½ inch deep for SF-2.0 and SF-3.0. According to ACI 301-10, bug holes or other surface voids exceeding these dimensions for the specified surface finish are defects and must be repaired. Otherwise, bug holes are allowed and considered surface imperfections, commonly referred to by ACI as surface effects.

The specifications for the project may limit the size of bug holes by specifying maximum widths and/or depths of surface voids. Review Section 03300 Cast-in-Place Concrete of the specifications for the project, especially the sections on Form-Facing Materials, Formwork, Finishing Formed Surfaces, and Concrete Surface Repairs.

Whether your bug holes are defects or not depends on:

  • The version of ACI 301 specified;
  • The size of the bug holes (the width and depth); and
  • The void size limitations, if specified by the contract.

If ACI 301-05 was specified and the contract documents did not limit the size of surface voids, bug holes are not defects but surface effects. If ACI 301-10 applies and SF-1.0, SF-2.0 or SF-3.0 was specified, or the specifications established a maximum void size, then only the bug holes that exceed the maximum allowable void size are defects. Otherwise, bug holes are surface effects. Only agree to repair those classified as surface defects.

If the owner wants a bug hole-free surface, then a smooth-rubbed or grout-cleaned rubbed finish as defined in ACI 301 should be specified. Create a smooth-rubbed finish by rubbing the wetted concrete surface with a carborundum brick within a day of formwork removal. This generates paste to create a uniform surface color and texture.

Read More

Hill and Griffith Customer Service

We're known for our hands on approach. Let us visit your plant and recommend concrete release agents, packerhead concrete form releases, concrete form seasoning, potable water concrete form release, non-petroleum concrete form release, biodegradable concrete form release, rust inhibitors and concrete dissolver products that suit your needs.

Hill and Griffith Samples

Product Samples

We are pleased to provide samples in quantities large enough to allow you to "try before you buy."
Contact Us »

 

Hill and Griffith Customer Service

Technical Services & Support

On-site casting defect investigations, product testing, machine start-ups and much more. Also, lab facilities are available to provide testing upon request.
Contact Us »

 

 Bulletins and Technical Papers for Concrete Casting Products

Tags: Concrete, Casting Solutions, Concrete Casting Products, Concrete Casting Supplies, Concrete Casting, Precast Concrete, Concrete Form Release Agent, Concrete Construction Magazine

Subscribe to Concrete News

Concrete Posts

Concrete Casting News Categories

see all