<img alt="" src="https://secure.hims1nice.com/150891.png" style="display:none;">

Green Sand Metalcasting Foundry News

Printing Long, Thin Cores for Aluminum Sand Casting

Posted by Hill and Griffith Company on Jan 21, 2020 8:00:00 AM

While the use of printed sand molds and cores has become increasingly common, two researchers investigated whether longer, thinner cores could hold up during the metalcasting process.

Article excerpt from the Casting Source November 2015 issue by Tom Mueller and Larry Andre.

One of metalcasting’s major advantages, when compared to other methods of manufacturing, is its ability to produce geometrically complex components. Metalcasting allows designers to put metal only where it’s needed because liquid metal can flow into the open mold cavity. Often, cores are placed into a mold to form an interior part of a casting. These inserts, often made of sand, prevent the molten metal from filling the entire mold, so interior cavities can be included in the casting design.

In recent years, the growth of 3-D printing capabilities has become a topic of interest for every manufacturing industry. In metalcasting, the process offers the potential of producing complex molds and cores with desirable mechanical and physical properties. Printed cores and molds allow for immediate evaluation of design iterations without the additional costs and lead time associated with tooling, which speed the development of cast components for end users.

Aluminum Castings Porosity Defects

While many sand casting suppliers are experienced with printed cores and molds, little research has been done into the performance of long, thin cores. Larger cores generally are able to handle the forces exerted during the flow of metal during the casting process, but less robust designs are relatively untested.

In the research paper, “Performance of Long, Thin Printed Cores in Aluminum Castings,” two researchers evaluated the performance of printed cores that covered a range of diameters and lengths. The primary aims of the study were to see whether cores were strong enough to hold up during pouring and whether gases could be vented from the mold through internal passages in the core.

If longer and/or thinner printed cores can be integrated into castings, engineers will have more freedom in designing interior cavities in castings. The potential increased complexity offered by these 3-D printed cores could lead to reduced costs and lead times for casting customers.

Testing the Tubes

For the A356 aluminum castings, tubes with wall thicknesses of 0.06-in. were created with internal diameters ranging from 0.25 to 0.875 in. and lengths ranging from 2 to 12 in. Printed cores were used to form the internal diameters, and the cores were printed with internal vents for gases generated during casting.

To ensure conditions were consistent, all tubes of the same diameter were cast at the same time and were fed from a common feeder at the bottom of the tube. Figure 1 shows the tubes, feeder and two down sprues, which increased the feed rate so the tubes would fill before freezing off. The tapered area at the end of each tube was a riser to feed the tube as metal shrunk during solidification.

Aluminum Castings 1

This design allowed the use of a single core for all six tubes of the same diameter. The core resembled a harp with a core print surrounding the cores, and the cores running parallel between them like strings on the harp. Figure 2 shows the CAD model of the core, which contains a passage through the base to allow the tubes to be bottom fed. The core would be extremely difficult if not impossible to create by conventional means.

To create the molds, matchplates were created for each of the tube diameters, is shown in Figure 3. The matchplate included vent lines that would connect the vents from each of the cores to the outside of the mold. Each of the mold cavities also was vented to the outside to allow complete filling of the mold.

The molds were positioned so that they were vertically parted. The pouring cups were elevated to increase the static pressure of the metal during pouring. A vacuum manifold was attached to the mold where the vent lines emerged so that a low level vacuum (supplied by a shop vacuum) could be used to assist in drawing out gases generated during filling.

On the first casting, the pouring cup was positioned 2 ft. above the mold, which filled quickly and metal flowed up and out of the vents. On successive casts, the head height was reduced until it was found that a head height of 3 in. sufficed.

In all, 12 pours were done, two for each of the six core diameters. Table 1 summarizes the 12 pours. After each pour, the casting was allowed to cool and broken out. The tubes were cut from the feeder and inspected. Each tube was visually inspected followed by X-ray and liquid penetrant inspection.

Figure 4 shows all 12 sets of tubes. Each smaller picture contains two sets of tubes, all with the same inner diameter, and two tubes of each of the six lengths of core.

Looking for Defects

The tubes were first evaluated for defects during pouring. Figure 5 shows an end view of one of each diameter of tubes. There is an obvious eccentricity of the core in the 0.25-in. tube, but the others appeared concentric. The lack of deformation in the larger diameter tubes was confirmed by X-ray inspection. The deformation of the small tube was great enough that, in longer lengths, part of the tube did not fill, as shown in Figure 6. Non-fill due to core deformation is clearly visible in the 8-, 10- and 12-in. tubes. Non-fill conditions were not found in any larger diameter tubes.

Liquid penetrant inspection revealed a number of gas defects, such as those shown in Figure 7. In some cases, a pit is obvious in the cases of larger defects. The presence of the gas defects raised two questions: What was the source of the gas? Why didn’t the core venting allow the gas to escape?

Read more


More News from Casting Source

When to Choose Casting

Vacuum Process Cuts Costs by 80% Over Machined Billet

7 Questions to Ask a Potential Casting Supplier


Hill and Griffith Customer Service

The Hill and Griffith Company's green sand metal casting foundry supplies help achieve the EPA's M.A.C.T. standards and reduce Benzene emissions. Our variety of environmentally sound release agents, coatings, partings, lubricants, core oils and specialty products will help you meet your metal casting's needs. We're known for our hands-on approach. Let us visit your plant and recommend products that suit your needs.

 

Hill and Griffith SamplesProduct Samples

We are pleased to provide samples in quantities large enough to allow you to "try before you buy."
Contact Us »

 

 

Hill and Griffith Customer ServiceTechnical Services & Support

On-site casting defect investigations, product testing, machine start-ups and much more. Also, lab facilities are available to provide testing upon request.
Contact Us »

 

Bulletins and Technical Papers for Metal Casting Products

Tags: Green Sand Casting Products, Green Sand Foundry Supply, Foundry Supply, Green Sand Release Agents, Foundry Supplies, Casting Source Magazine

Subscribe to the Green Sand Metal Casting News

Recent Metalcasting News

Follow Me

Metalcasting News Categories

see all