<img alt="" src="https://secure.hims1nice.com/150891.png" style="display:none;">

Green Sand Metalcasting Foundry News

Green Sand Metalcasting Foundry, Sodium Silicate Binders

Posted by Hill and Griffith Company on May 29, 2019 11:36:12 PM

Hill and Griffith Sodium Silicate Binders are formulated with water based solutions of Sodium Silicates and collapsibility agents.

These binders are available in various percentages of carbonaceous materials as well as silica to soda ratios for varied or specific applications. The sand and silicate mixture is hardened by gassing with carbon dioxide (CO2). Molds or cores produced with Silicate binders result in castings with minimal veining, scabbing and penetration. Due to lack of mold wall movement, dimensional accuracy may be improved over some other casting processes.



  • No Pollution Problems
  • No Need For Heat Curing
  • Odorless
  • No Organic Solvents
  • Good Bench Life When Protected From Drying Out
  • Excellent Flowability

Typical Product Data

  Ratio Density Viscosity (cps)  Organic Content
Corosil GL 2.58 12.66 1480 10.0
Corosil GN 2.40 12.42 760 17.0
Corosil GR 2.40 12.32 260 5.0
Corosil GU 2.40 13.00 1110 0.0
Corosil GX 2.40 12.32 375 5.0

General Information:

CoBond binder is a solution of sodium silicates that can be hardened on sand by a reaction with carbon dioxide. The curing process is quick and requires no heat. Therefore production rates are higher with a minimum of energy expenditure. There are no pollution problems with CoBond binder during mixing, gassing, casting, or shakeout because both the CoBond binder and carbon dioxide are odorless. CoBond binder contains no solvents and because it is nitrogen free it is suitable for steel castings. CoBond binder is characterized by the silica (SiO2) and soda (Na2O) ratio, specific gravity and viscosity. The specific gravity and viscosity determine the flowability of the sand mix while the silica (SiO2) to soda (Na2O) ratio determines the rate of cure and the strength properties of the sand. CoBond binder is supplied with silica (SiO2) to soda (Na2O) ratios from 2.00 to 2.58. In some CoBondbinders, organic additives have been added to improve collapsibility. Practice indicates that the higher the organic content the better the collapsibility.

Curing Reaction:

When a sodium silicate solution is mixed on sand and then cured with CO2, complex chemical and physical changes occur that contribute to the hardening of the core or mold. The bonding phase that holds the sand together consists of (1) precipitated silica gel formed as a result of the reaction between CO2 and sodium hydroxide and the accompanying pH change and (2) dehydrated sodium silicate formed by removal of water as air passes through the sand.

The strength of a CO2 silicate cured core or mold depends primarily on the amount of the silica gel that is formed. Gassing parameters (pressure, flow-rate, CO2 concentration, gas time) are important in controlling strength. The most efficient use of CO2, is obtained by using low flow rates and reduced concentrations of CO2. This ensures that the CO2 remains in contact with the binder long enough to start curing, rather than being blown through quickly and at such high concentrations that much of it is wasted. It is more important to control flow rate than gassing pressure to obtain efficient CO2 use, which is typically 1.5% based on silicate.

If the maximum storage life is needed for a core or mold made with CoBond binder, then the minimum amount of gas needed to get acceptable strengths out of the box should be used. As the core of mold sits in the air, the binder will continue to cure and the strength will build up over a period of several days. If high strengths are needed only in the early stages of cure and storage time, then more gas should be used in the early stages of initial strengths. Cores or molds can actually over cure when stored. Low strengths at pouring can give improved collapsibility.

Handling Suggestions:

Nearly all types of foundry sands can be bonded with CoBond binder. Usually silica, lake, and bank sands of 45-130 grain fineness are used. Other sand types, as well as reclaimed sand, can be used providing they are not highly acidic. The moisture content of the sand should be less than 0.5% and the sand temperature between 55o - 95o F. (Hot sand shortens bench life and cold sands reduce flowability).

Use Levels:

For sand of grain fineness 30 - 50 the recommended binder level is 2 - 4 %. For sands of grain fineness number 50 - 80 the recommended binder level is 3 - 5 %. For sands of grain fineness number 80 - 160 the recommended binder level is 4 - 6 %.


Kaolin, ball clay, fire clay or calcined alumina can be added at 1 - 2 % based on sand to increase hot strength. Seacoal at 3 - 5 %, iron oxide at 2 - 3 %, or pitch at 1 - 2 % will improve collapsibility. Any dry additive should be added to the sand before the CoBond

Mixing Equipment:

A mulling type mixing process is recommended. Mixing should be thorough but not too long. A total mixing time of 3 - 4 minutes is usually adequate. Short mixing times prevent heat build up and loss of water by evaporation. All mixes should be covered to prevent loss of water by evaporation.


The curing of a sodium silicate solution mixed with sand is the result of complex changes that contribute to the hardening of the core or mold. Usually theCO2 flow rate is 1 - 5 % based on silicate. Use a dry CO2 as water is detrimental to gassing speed and overall strengths. Phenolphthalein, at a level of 0.75 % based on sand, may be used as an indicator. The sand will appear red and areas that have been adequately gassed will become colorless; therefore, any red areas would require further gassing to start the curing reaction.


Water based coatings should not be used with CoBond bonded sand because the binder will dissolve in water and the core will soften. For best results, use either alcohol or chlorinated based washes.


All CoBond and Corosil products should be protected from freezing. However, should freezing occur, the CoBond product may be restored to usable form by allowing the contents to come to room temperature and thoroughly mixing the product. For best results, store between 55 - 95o F. Containers should be closed as completely as possible to prevent exposure to CO2 and to prevent changes in viscosity due to water evaporation.

Safety Precautions:

In general, Cobond binder is manufactured using components having low order of toxicity. Fluid or vapor in the eyes or on the skin may cause transitory irritation that disappears within 24 hours. Flushing the eyes with flowing water and washing the skin with soap and water will usually prevent discomfort. If irritation persists, consult a physician. Material Safety Data Sheets outlining known hazards and safety precautions associated with the product are available and should be used accordingly.

Download Printable Document (MS Word .doc) by Clicking Here

Hill and Griffith Customer Service

The Hill and Griffith Company's green sand metalcasting foundry supplies help achieve the EPA's M.A.C.T. standards and reduce Benzene emissions. Our variety of environmentally sound release agents, coatings, partings, lubricants, core oils and specialty products will help you meet your metal casting's needs. We're known for our hands on approach. Let us visit your plant and recommend products that suit your needs.

Hill and Griffith Samples

Product Samples

We are pleased to provide samples in quantities large enough to allow you to "try before you buy."
Contact Us »


Hill and Griffith Customer Service

Technical Services & Support

On-site casting defect investigations, product testing, machine start-ups and much more. Also, lab facilities are available to provide testing upon request.
Contact Us »

Bulletins and Technical Papers for Metal Casting Products


Tags: Green Sand Casting Products, Green Sand Foundry Supply, Foundry Supply, Foundry Supplies, Sodium Silicate Binders

Subscribe to the Green Sand Metal Casting News

Recent Metalcasting News

Follow Me

Metalcasting News Categories

see all